Aurora Bearing Product Catalog 319

A U R O R A B E A R I N G C O M P A N Y COMMERCIAL | MILITARY | AIRCRAFT The Motion-Transfer Specialists ROD END & SPHERICAL BEARING CATALOG & RESOURCE GUIDE 319

www.aurorabearing.com • Fax 630-859-0971 AURORA BEARING COMPANY Basic Information...............................................................................................................................4-7 Inch Rod End and Spherical Bearings SPM & SPB Male Rod Ends ................................................................................................................................. 8 SPW & SPG Series Female Rod Ends ................................................................................................................. 9 CM & CB Series Male Rod Ends......................................................................................................................... 10 CW & CG Series Female Rod Ends.................................................................................................................... 11 VCM & VCB Series Male Rod Ends .................................................................................................................... 12 VCW & VCG Series Female Rod Ends ............................................................................................................... 13 CAM & CAB Series Male Rod Ends .................................................................................................................... 14 VCAM & VCAB Series Male Rod Ends ............................................................................................................... 15 BM & BB Series Male Rod Ends ......................................................................................................................... 16 BW & BG Series Female Rod Ends .................................................................................................................... 17 MM & MB Series Male Rod Ends ........................................................................................................................ 18 MW & MG Series Female Rod Ends ................................................................................................................... 19 XM & XB Series Male Rod Ends ......................................................................................................................... 20 Aurora Bearing Factory ....................................................................................................................................... 21 KM & KB Series Male Rod Ends ......................................................................................................................... 22 KW & KG Series Female Rod Ends .................................................................................................................... 23 SM & SB Series Male Rod Ends ......................................................................................................................... 24 SW & SG Series Female Rod Ends .................................................................................................................... 25 CM-ET & CB-ET Series Stainless Steel Male Rod Ends .................................................................................... 26 CW-ET & CG-ET Series Stainless Steel Female Rod Ends ............................................................................... 27 SM-E & SB-E Series Stainless Steel Male Rod Ends ......................................................................................... 28 SW-E & SG-E Series Stainless Steel Female Rod Ends .................................................................................... 29 Large Bore Series Male Rod Ends ...................................................................................................................... 30 Large Bore Series Female Rod Ends.................................................................................................................. 31 Large Bore Series Male Rod Ends ...................................................................................................................... 32 Large Bore Series Female Rod Ends.................................................................................................................. 33 AM & AB Series Male Rod Ends ......................................................................................................................... 34 AW & AG Series Female Rod Ends .................................................................................................................... 35 XAM & XAB Series Male Rod Ends .................................................................................................................... 36 AM/XAM Series Special Size .............................................................................................................................. 37 RAM, RAB, RXAM, RXAB Series Male Rod Ends .............................................................................................. 38 RAM/RXAM Series Special Size ......................................................................................................................... 39 Performance Racing Series............................................................................................................................40-41 High Misalignment Series Male Rod Ends .......................................................................................................... 42 Linkages .............................................................................................................................................................. 43 COM & HCOM Series Spherical Bearings .......................................................................................................... 44 COM-KH & HCOM-KH Series Spherical Bearings .............................................................................................. 45 COM-E Series Spherical Bearings ...................................................................................................................... 46 LCOM Series Large Size Spherical Bearings...................................................................................................... 47 MIB Series ........................................................................................................................................................... 48 AIB Series............................................................................................................................................................ 49 SIB Series............................................................................................................................................................ 50 High Misalignment Series Spherical Bearings..................................................................................................... 51 Performance Racing Series............................................................................................................................52-53 Metric Rod End and Spherical Bearings CM-M & CB-M Series Male Rod Ends - Metric .................................................................................................. 54 CW-M & CG-M Series Female Rod Ends - Metric ............................................................................................ 55 Contents Page No.

www.aurorabearing.com • Fax 630-859-0971 3 AURORA BEARING COMPANY Contents MM-M & MB-M Series Male Rod Ends - Metric .................................................................................................. 56 MW-M & MG-M Series Female Rod Ends - Metric.............................................................................................. 57 KM-M & KB-M Series Male Rod Ends - Metric.................................................................................................... 58 KW-M & KG-M Series Female Rod Ends - Metric............................................................................................... 59 AM-M & AB-M Series Male Rod Ends - Metric.................................................................................................... 60 AW-M & AG-M Series Female Rod Ends - Metric............................................................................................... 61 COM-M Series Spherical Bearings - Metric......................................................................................................... 62 Fractured Race Bearings..................................................................................................................................... 63 Spherical Plain Bearings.................................................................................................................................64-67 Angular Contact Spherical Plain Bearings........................................................................................................... 68 Fractured Race Bearing Option........................................................................................................................... 69 Spherical Plain Bearings.................................................................................................................................70-73 Angular Contact Spherical Plain Bearings......................................................................................................74-75 Fractured Race Bearings Interchange Guide. ..................................................................................................... 76 HB Series............................................................................................................................................................. 77 Rod End Studs..................................................................................................................................................... 78 Jam Nuts.............................................................................................................................................................. 79 Lubrication Fittings............................................................................................................................................... 80 SAE Specification Bearings................................................................................................................................. 81 ANC-T & ANC-TG Spherical Bearings............................................................................................................82-83 AWC-T & AWC-TG Spherical Bearings..........................................................................................................84-85 ASM-T & ASB-T Male Rod Ends....................................................................................................................86-87 ASW-T & ASG-T Female Rod Ends...............................................................................................................88-89 ATM-T & ATB-T Male Rod Ends.....................................................................................................................90-91 ATW-T & ATG-T Female Rod Ends................................................................................................................92-93 ASM-ET & ASB-ET Male Rod Ends. ..............................................................................................................94-95 ASW-ET & ASG-ET Female Rod Ends. .........................................................................................................96-97 ATM-ET & ATB-ET Male Rod Ends................................................................................................................98-99 ATW-ET & ATG-ET Female Rod Ends.......................................................................................................100-101 AJB-TA/-TC Straight Journal Bearings.......................................................................................................102-103 AJB-TFA/-TFC Flanged Journal Bearings..................................................................................................104-105 GMM-M & GMB-M Series Male Rod Ends. ....................................................................................................... 106 GMW-M & GMG-M Series Female Rod Ends. .................................................................................................. 107 Aircraft and Military Special Products................................................................................................................ 108 Special Size Race Car Parts.............................................................................................................................. 109 Special Size Race Car Spherical Bearings........................................................................................................ 110 Technical Resources. ........................................................................................................................................ 111 Suggested Housing Bores..........................................................................................................................112-114 Suggested Shaft Sizes................................................................................................................................115-116 Installation of Spherical Bearing. ....................................................................................................................... 117 Installation of Spherical Bearing with Staking Grooves Tools and Staking Methods......................................... 118 Stake and Groove Type Chart........................................................................................................................... 119 PTFE Liner Specifications.................................................................................................................................. 120 Temperature Limits............................................................................................................................................ 121 Frequently Asked Questions.............................................................................................................................. 122 Reference. ......................................................................................................................................................... 123 Engineering Information..................................................................................................................................... 124 Terms Translations.....................................................................................................................................125-126 2D and 3D CAD DRAWINGS of Aurora Bearing Rod End and Spherical Bearings.......................................... 127 Page No.

www.aurorabearing.com • Fax 630-859-0971 4 AURORA BEARING COMPANY GENERAL INFORMATION In 1971 a new company entered the rod end and spherical bearing marketplace. This new firm, Aurora Bearing Company, soon became a major force in the rod end industry. Known primarily for a high quality product and a strong commitment to customer service, the firm dramatically increased its market coverage and now serves nearly every industry and aerospace market. These markets include among others: textile and packaging machinery, machine tools, business machines, recreation and exercise equipment, agricultural and off highway vehicles, commercial transportation and high performance racing vehicles as well as military equipment and commercial air and spacecraft. Over the years, Aurora Bearing has retained its original business philosophy of furnishing a high quality product at competitive prices. In addition, the company’s initial goals of providing prompt delivery and furnishing service with a personal touch have been rigidly maintained. Aurora Bearing offers a complete line of standard rod end and spherical bearings. We also design and manufacture special bearings to meet a variety of applications that require custom engineered units or special materials. Now marketing products worldwide, Aurora Bearing fields a very competent sales force that is available to assist and provide you with a practical and sound solution to rod end and spherical bearing application problems and challenges. PRODUCT INFORMATION ENGINEERING DATA AND ROD ENDS Aurora Bearing Company rod ends are, unless noted, manufactured utilizing two construction styles. They are of the two or three-piece type. Both are made with the solid, or onepiece, race construction method and feature the advantages of metal-to-metal contact between bearing components. (PTFE to metal interface may also be incorporated when specified). The standard two-piece style consists of a body and precision ground heat treated steel ball. This type of construction allows the rod end body to carry a greater radial static load. This configuration also offers greater misalignment capabilities. A variety of materials and plating options for the component parts in this series are available. Any cold-formable steel in the stainless and alloy steel categories can be specified for the body, and all hardenable alloys such as 52100 and 440C stainless steel may be employed for the ball component. The three-piece style consists of a body, ball and race. This type of unit, offering fully swaged bearing construction, features the advantages of optimized spherical conformity between the ball and race. It also offers flexibility in that many different types of materials can be interchanged in each component part, providing combinations that can be tailored to meet just about any application requirement. The SPM/SPW series features a proprietary molded liner system with low friction and low moisture absorbing properties. Consult our engineering department for materials to fit your special application. Materials used in the standard catalog items are outlined on the appropriate detail page. SPHERICAL BEARINGS These bearings incorporate the single piece race type construction, providing optimized ball-to-race conformity. They can be re-lubricated through an annular groove in the outer race with two interconnecting holes positioned at 180 degrees. Various metals may also be substituted in these types of units to meet special requirements. Recommended housing bores are given on pages 112-114. PTFE LINED ROD ENDS AND SPHERICAL BEARINGS Composite PTFE lined races are available as noted in most rod end bearing units and all spherical bearings. The steel race has a self-lubricating liner; a PTFE impregnated woven fabric, chemically bonded to the inner diameter of the race, and is denoted by the suffix “T”. All Aurora Bearing liner style options are maintenance free and offer improved frictional characteristics. They have been developed by Aurora engineers specifically for bearing use, and are exclusive to Aurora Bearing products. Except as noted, AT1400 is supplied as the standard liner in all commercial units. It is designed primarily to satisfy the demands of the commercial/industrial market as well as most high performance applications. This liner can be used in temperatures ranging from -65° to +250° F. AT3200 is an ultra-high performance liner qualified to SAE-AS81820 Type A, developed for military and aircraft/ aerospace applications. This liner offers higher load carrying capacity as well as greatly increased dynamic wear characteristics and can be used in temperatures ranging from -65° to +325° F. This liner is standard on all military specification bearings manufactured by Aurora Bearing, as well as certain high performance commercial bearings as used in the automotive racing industry. It can also be specified on other lined products manufactured by Aurora Bearing where demanding applications require its superior performance characteristics. AT2100 is used in commercial units with stainless steel race construction. It is tailored for applications with aqueous environments. Aurora 2 piece rod ends with the prefix “V” use Aurora’s steel backed PTFE composite liner, resulting in the benefits of a PTFE lined bearing at an economical price. Aurora Bearing also has available a variety of alternate liner configurations to suit special requirements. Information on these and other liner configurations can be found on page 120. Manufacturing and worldwide supplier of the highest quality rod ends and spherical bearings - anywhere!

www.aurorabearing.com • Fax 630-859-0971 5 ULTIMATE RADIAL STATIC LOAD CAPACITY ROD ENDS The ultimate radial static load capacity is based upon the minimum mechanical properties of the design configuration in the stressed area. The ultimate radial static load capacity called out in the rod end specification charts is defined as a single cycle, unidirectional applied load to cause ultimate failure. Operating loads should be based on the static load ratings, incorporating appropriate safety factors to suit the application. When a rod end or spherical bearing is to be applied in full rotation, the surface speed of the ball should be kept below 20 feet per minute or the rotational speed should be below 100 RPM, whichever is lower, with the operating loads not to exceed 10% of the ultimate radial static load. Load ratings listed in the standard detail pages are applicable to rod ends supplied without grease fittings. Load ratings for units employing fittings may be affected due to lighter cross section in the stressed area. For information on the rod end radial static load ratings with fittings and other specific load rating information, consult the Aurora Bearing engineering department. AXIAL STATIC LOAD CAPACITY ROD ENDS Axial static load capacity is the force that is applied through the bore of the ball. For Aurora two-piece rod ends, maximum axial static load capacity is recommended to be 15 percent of the ultimate radial static load capacity. For three-piece rod ends, maximum axial static load capacity is generally recommended as 10 percent of ultimate radial static load capacity. It should be noted, however, that on three-piece units factors such as race material, body material and dimensions may affect axial static load capacity. For further information, consult the Aurora Bearing engineering department. RADIAL STATIC LIMIT LOAD CAPACITY SPHERICAL BEARINGS Unless otherwise noted, radial static loads are maximum static based on the maximum permanent set in the bearing race of 0.2% of the ball diameter. If greater permanent set can be allowed or if alternate race materials are used consult our engineering department for change factors. Operating loads are based on the radial static load rating and appropriate safety factors should be utilized to suit the application. Max axial load is recommended at 20 percent of the radial static load. Extreme care should be used on selecting a sufficiently strong housing to accept this type of bearing. BEARING MISALIGNMENT A rod end or spherical bearing’s ability to misalign is measured by the degree of angle the ball can accommodate without interference. The angle of misalignment in a rod end is limited by the ball width and head diameter as shown in figure 1. This arrangement is called a clevis mount, and is the type represented in the standard rod end detail pages. If added misalignment is necessary, this can be accomplished by utilizing spacers between the clevis mounting and ball face, or by using special rod ends designed to meet specific requirements. Misalignment angle in a spherical bearing is limited by the ball and race width with respect to the ball diameter, illustrated in figure 3. This is the mounting type represented in the standard detail pages for spherical bearings. Mounting arrangements for spherical bearings such as shown in figures 2 through 4 are also used with rod ends. The misalignment angle is then calculated by selecting the proper formula. ANGLE OF MISALIGNMENT a1 a1 FIGURE 1 FIGURE 3 FIGURE 2 a1 = Sin-1 W - Sin-1 H a2 = Sin-1 W - Sin-1 H FIGURE 4 a3 = Sin-1 W - Sin-1 H a2 a2 a3 a3 a4 a4 Reference Letters B - Ball Bore M - Outer Race Chamfer D - Head Diameter of Outer Race Diameter R - Ball Diameter H - Housing Width A - (D-2M)2 + H2 W - Ball Width D D A A R R a4 = Cos-1 B - Sin-1 H R R

www.aurorabearing.com • Fax 630-859-0971 6 1970s Aurora Bearing Catalog

www.aurorabearing.com • Fax 630-859-0971 7 3-PIECE AND 2-PIECE BEARING DESIGN 3-Piece Unit NOTE - Re-Lube hole for lubrication through shank of housing. Single piece race, steel, heat-treated (optional), features swaged construction for maximum performance. Alternate race materials available to suit your application. Note extension of race beyond width of housing in the prestaking position. After staking, the sides of race have been upset into chamfers. Ball is subsequently loosened holding close tolerance fits between ball and race. HOUSING INSERT ASSEMBLED HOUSING AND INSERT IN PRE-STAKING POSITION Consists of BALL and RACE ASSEMBLED HOUSING AND INSERT IN STAKED POSITION Chamfers on both sides 2-Piece Unit Housing ready for swaging Precision ground ball - (available in alternate materials) - for close tolerance fits. Housing and Ball in pre-swaging position. Sides of housing are closed around ball for maximum strength unit.

www.aurorabearing.com • Fax 630-859-0971 8 SPM & SPB SERIES MALE ROD ENDS Molded Race – Economy SPM-3 SPM-4 SPM-5 SPM-6 SPM-7 SPM-8 SPM-10 SPM-12 SPB-3 SPB-4 SPB-5 SPB-6 SPB-7 SPB-8 SPB-10 SPB-12 4.826 6.350 7.938 9.525 11.113 12.700 15.875 19.050 7.92 9.53 11.10 12.70 14.27 15.88 19.05 22.23 6.35 7.14 8.74 10.31 11.10 12.70 14.27 17.45 31.75 39.67 47.63 49.23 53.98 61.93 66.68 73.03 15.88 19.05 22.23 25.40 28.58 33.32 38.10 44.45 11.10 12.70 15.88 18.26 20.62 23.80 28.58 33.32 19.05 25.40 31.75 31.75 33.33 38.10 41.28 44.45 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 13 16 14 12 14 12 16 14 5,382 10,987 12,188 18,726 23,797 28,601 36,918 48,483 10 18 32 49 67 105 165 258 Left Hand B + .051 -.000 W ± .13 H Ref. A + 1.52 - .76 D ± .38 Ball Dia. Ref. C ± 1.57 Thread UNF-2A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand This series features a molded race compound designed to provide low friction, low moisture absorbing properties. SPM-3 SPM-4 SPM-5 SPM-6 SPM-7 SPM-8 SPM-10 SPM-12 SPB-3 SPB-4 SPB-5 SPB-6 SPB-7 SPB-8 SPB-10 SPB-12 .1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .312 .375 .437 .500 .562 .625 .750 .875 .250 .281 .344 .406 .437 .500 .562 .687 1.250 1.562 1.875 1.938 2.125 2.438 2.625 2.875 .625 .750 .875 1.000 1.125 1.312 1.500 1.750 .437 .500 .625 .719 .812 .937 1.125 1.312 .750 1.000 1.250 1.250 1.312 1.500 1.625 1.750 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 13 16 14 12 14 12 16 14 1,210 2,470 2,740 4,210 5,350 6,430 8,300 10,900 .02 .04 .07 .11 .15 .23 .36 .57 Left Hand B + .0020 -.0000 W ± .005 H Ref. A + .060 - .030 D ± .015 Ball Dia. Ref. C ± .062 Thread UNF-2A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Right Hand Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Race - Molded, selflubricating, reinforced Nylon. Notes - All sizes available with studs upon request. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 9 SPW & SPG SERIES FEMALE ROD ENDS Molded Race – Economy Left Hand B + .051 -.000 W ± .13 H Ref. A + 1.52 - .76 D ± .38 K ± .38 J ± .38 Ball Dia. Ref. C ± 1.57 Thread UNF-2B ROD END NO. DIMENSIONS IN MILLIMETERS This series features a molded race compound designed to provide low friction, low moisture absorbing properties. SPW-3 SPW-4 SPW-5 SPW-6 SPW-7 SPW-8 SPW-10 SPW-12 SPG-3 SPG-4 SPG-5 SPG-6 SPG-7 SPG-8 SPG-10 SPG-12 4.826 6.350 7.938 9.525 11.113 12.700 15.875 19.050 7.92 9.53 11.10 12.70 14.27 15.88 19.05 22.23 6.35 7.14 8.74 10.31 11.10 12.70 14.27 17.45 26.97 33.32 34.93 41.28 46.02 53.98 63.50 73.03 15.88 19.05 22.23 25.40 28.58 33.32 38.10 44.45 10.31 11.91 12.70 17.45 19.05 22.23 25.40 28.58 7.92 9.53 11.10 14.27 15.88 19.05 22.23 25.40 11.10 12.70 15.88 18.26 20.62 23.80 28.58 33.32 14.27 19.05 19.05 23.80 26.97 30.15 38.10 44.45 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-12 13 16 14 12 14 12 16 14 Right Hand a° Misalign. Angle 5,382 10,987 12,188 18,237 23,797 28,601 36,918 48,483 17 27 35 66 87 142 210 305 Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams Left Hand B + .0020 -.0000 W ± .005 H Ref. A + .060 - .030 D ± .015 K ± .015 J ± .015 Ball Dia. Ref. C ± .062 Thread UNF-2B ROD END NO. DIMENSIONS IN INCHES SPW-3 SPW-4 SPW-5 SPW-6 SPW-7 SPW-8 SPW-10 SPW-12 SPG-3 SPG-4 SPG-5 SPG-6 SPG-7 SPG-8 SPG-10 SPG-12 .1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .312 .375 .437 .500 .562 .625 .750 .875 .250 .281 .344 .406 .437 .500 .562 .687 1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875 .625 .750 .875 1.000 1.125 1.312 1.500 1.750 .406 .469 .500 .687 .750 .875 1.000 1.125 .312 .375 .437 .562 .625 .750 .875 1.000 .437 .500 .625 .719 .812 .937 1.125 1.312 .562 .750 .750 .937 1.062 1.187 1.500 1.562 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 13 16 14 12 14 12 16 14 Right Hand a° Misalign. Angle 1,210 2,470 2,740 4,100 5,350 6,430 8,300 10,900 .04 .06 .08 .15 .19 .31 .46 .67 Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Race - Molded, selflubricating, reinforced Nylon. Notes - All sizes available with studs upon request. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 10 CM & CB SERIES MALE ROD ENDS General Purpose - Economy CM-3* CM-4* CM-5* CM-6 CM-7 CM-8 CM-10 CM-12 CB-3* CB-4* CB-5* CB-6 CB-7 CB-8 CB-10 CB-12 .1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .312 .375 .437 .500 .562 .625 .750 .875 .234 .250 .312 .359 .406 .453 .484 .593 1.250 1.562 1.875 1.938 2.125 2.438 2.625 2.875 .625 .750 .875 1.000 1.125 1.312 1.500 1.750 .437 .500 .625 .719 .812 .937 1.125 1.312 .750 1.000 1.250 1.250 1.375 1.500 1.625 1.750 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 20 27 22 22 21 20 26 24 1,204 2,212 3,577 5,068 6,345 8,338 9,713 14,207 .03 .04 .07 .11 .15 .24 .36 .57 Left Hand B + .0025 -.0005 W ± .005 H Ref. A ± .015 D Ref. Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Right Hand CM-3* CM-4* CM-5* CM-6 CM-7 CM-8 CM-10 CM-12 CB-3* CB-4* CB-5* CB-6 CB-7 CB-8 CB-10 CB-12 4.826 6.350 7.938 9.525 11.113 12.700 15.875 19.050 7.92 9.53 11.10 12.70 14.27 15.88 19.05 22.23 5.94 6.35 7.92 9.12 10.31 11.50 12.29 15.06 31.75 39.67 47.63 49.23 53.98 61.93 66.68 73.03 15.88 19.05 22.23 25.40 28.58 33.32 38.10 44.45 11.10 12.70 15.88 18.26 20.62 23.80 28.58 33.32 19.05 25.40 31.75 31.75 34.93 38.10 41.28 44.45 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 20 27 22 22 21 20 26 24 5,355 9,839 15,910 22,542 28,223 37,087 43,203 63,193 14 18 32 50 68 109 163 259 Left Hand B + .064 -.013 W ± .13 H Ref. A ± .38 D Ref. Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. * Grease fittings not available on these sizes. Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix as designated. Z Zerk type fitting Ex: CM-6Z F Flush type fitting Ex: CM-6F Load ratings apply only to rod ends without grease fittings. For load ratings with fittings, please consult our engineering department. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 11 CW & CG SERIES FEMALE ROD ENDS General Purpose - Economy CW-3* CW-4 CW-5 CW-6 CW-7 CW-8 CW-10 CW-12 CG-3* CG-4 CG-5 CG-6 CG-7 CG-8 CG-10 CG-12 4.826 6.350 7.938 9.525 11.113 12.700 15.875 19.050 7.92 9.53 11.10 12.70 14.27 15.88 19.05 22.23 5.94 6.35 7.92 9.12 10.31 11.50 12.29 15.06 26.97 33.32 34.93 41.28 46.02 53.98 63.50 73.03 15.88 19.05 22.23 25.40 28.58 33.32 38.10 44.45 10.31 11.91 12.70 17.45 19.05 22.23 25.40 28.58 7.92 9.53 11.10 14.27 15.88 19.05 22.23 25.40 11.10 12.70 15.88 18.26 20.62 23.80 28.58 33.32 12.70 17.45 17.45 20.62 23.80 26.97 34.93 39.67 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 20 27 22 22 21 20 26 24 Right Hand Left Hand† B + .064 -.013 W ± .13 H Ref. A ± .38 D Ref. K ± .25 J ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-2B a° Misalign. Angle 9,247 14,269 17,009 22,627 28,400 40,459 43,203 63,193 18 23 36 59 82 132 195 295 Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS CW-3* CW-4 CW-5 CW-6 CW-7 CW-8 CW-10 CW-12 CG-3* CG-4 CG-5 CG-6 CG-7 CG-8 CG-10 CG-12 .1900 .2500 .3125 .3750 .4375 .5000 .6250 .7500 .312 .375 .437 .500 .562 .625 .750 .875 .234 .250 .312 .359 .406 .453 .484 .593 1.062 1.312 1.375 1.625 1.812 2.125 2.500 2.875 .625 .750 .875 1.000 1.125 1.312 1.500 1.750 .406 .469 .500 .687 .750 .875 1.000 1.125 .312 .375 .437 .562 .625 .750 .875 1.000 .437 .500 .625 .719 .812 .937 1.125 1.312 .500 .687 .687 .812 .937 1.062 1.375 1.562 10-32 1/4-28 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 3/4-16 20 27 22 22 21 20 26 24 Right Hand Left Hand† B + .0025 -.0005 W ± .005 H Ref. A ± .015 D Ref. K ± .010 J ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-2B a° Misalign. Angle 2,079 3,208 3,824 5,087 6,385 9,096 9,713 14,207 .04 .05 .08 .13 .18 .29 .43 .65 Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. * Grease fittings not available on these sizes. Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix as designated. Z Zerk type fitting Ex: CW-6Z F Flush type fitting Ex: CW-6F †Left hand units have identification groove near end of shank. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 12 VCM & VCB SERIES MALE ROD ENDS General Purpose - Economy - Self-Lubricating Left Hand B + .0025 - .0005 W ± .005 H Ref. A ± .015 D Ref. Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Bushing - Steel Backed, PTFE Composite Notes - All sizes available with studs upon request. Right Hand VCM-5 VCB-5 .3125 .437 .312 1.875 .875 .593 1.250 5/16-24 18 2,623 .07 VCM-6 VCB-6 .3750 .500 .359 1.938 1.000 .687 1.250 3/8-24 18 3,643 .11 VCM-7 VCB-7 .4375 .562 .406 2.125 1.125 .781 1.375 7/16-20 17 4,464 .15 VCM-8 VCB-8 .5000 .625 .453 2.438 1.312 .875 1.500 1/2-20 16 7,229 .24 VCM-10 VCB-10 .6250 .750 .484 2.625 1.500 1.062 1.625 5/8-18 22 8,204 .36 VCM-12 VCB-12 .7500 .875 .593 2.875 1.750 1.250 1.750 3/4-16 20 12,280 .57 Left Hand B + .064 - .013 W ± .13 H Ref. A ± .38 D Ref. Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand VCM-5 VCB-5 7.938 11.10 7.92 47.63 22.23 15.06 31.75 5/16-24 18 11,667 32 VCM-6 VCB-6 9.525 12.70 9.12 49.23 25.40 17.45 31.75 3/8-24 18 16,204 50 VCM-7 VCB-7 11.113 14.27 10.31 53.98 28.58 19.84 34.93 7/16-20 17 19,856 68 VCM-8 VCB-8 12.700 15.88 11.50 61.93 33.32 22.23 38.10 1/2-20 16 32,155 109 VCM-10 VCB-10 15.875 19.05 12.29 66.68 38.10 26.97 41.28 5/8-18 22 36,491 163 VCM-12 VCB-12 19.050 22.23 15.06 73.03 44.45 31.75 44.45 3/4-16 20 54,621 259 Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 13 VCW & VCG SERIES FEMALE ROD ENDS General Purpose - Economy - Self-Lubricating Body - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Bushing - Steel Backed, PTFE Composite Notes - All sizes available with studs upon request. Left Hand† B + .0025 -.0005 W ± .005 H Ref. A ± .015 D Ref. K ± .010 J ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-2B ROD END NO. DIMENSIONS IN INCHES Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. VCW-5 VCG-5 .3125 .437 .312 1.375 .875 .500 .437 .593 .687 5/16-24 18 2,623 .08 VCW-6 VCG-6 .3750 .500 .359 1.625 1.000 .687 .562 .687 .812 3/8-24 18 3,643 .13 VCW-7 VCG-7 .4375 .562 .406 1.812 1.125 .750 .625 .781 .937 7/16-20 17 4,464 .18 VCW-8 VCG-8 .5000 .625 .453 2.125 1.312 .875 .750 .875 1.062 1/2-20 16 7,229 .29 VCW-10 VCG-10 .6250 .750 .484 2.500 1.500 1.000 .875 1.062 1.375 5/8-18 22 8,204 .43 VCW-12 VCG-12 .7500 .875 .593 2.875 1.750 1.125 1.000 1.250 1.562 3/4-16 20 12,280 .65 Left Hand† B + .064 -.013 W ± .13 H Ref. A ± .38 D Ref. K ± .25 J ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-2B ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams VCW-5 VCG-5 7.938 11.10 7.92 34.93 22.23 12.70 11.10 15.06 17.45 5/16-24 18 11,667 36 VCW-6 VCG-6 9.525 12.70 9.12 41.28 25.40 17.45 14.27 17.45 20.62 3/8-24 18 16,204 59 VCW-7 VCG-7 11.113 14.27 10.31 46.02 28.58 19.05 15.88 19.84 23.80 7/16-20 17 19,856 82 VCW-8 VCG-8 12.700 15.88 11.50 53.98 33.32 22.23 19.05 22.23 26.97 1/2-20 16 32,155 132 VCW-10 VCG-10 15.875 19.05 12.29 63.50 38.10 25.40 22.23 26.97 34.93 5/8-18 22 36,491 195 VCW-12 VCG-12 19.050 22.23 15.06 73.03 44.45 28.58 25.40 31.75 39.67 3/4-16 20 54,621 295 †Left hand units have identification groove near end of shank. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 14 CAM & CAB SERIES MALE ROD ENDS High Strength – Economy Series Left Hand B + .0025 - .0005 W + .005 H Ref. A ± .015 D Ref. Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Right Hand CAM-5 CAB-5 .3125 .437 .312 1.875 .875 .625 1.250 5/16-24 22 6,684 .07 CAM-6 CAB-6 .3750 .500 .359 1.938 1.000 .719 1.250 3/8-24 22 9,088 .11 CAM-7 CAB-7 .4375 .562 .406 2.125 1.125 .812 1.375 7/16-20 21 11,445 .15 CAM-8 CAB-8 .5000 .625 .453 2.438 1.312 .937 1.500 1/2-20 20 15,479 .24 CAM-10 CAB-10 .6250 .750 .484 2.625 1.500 1.125 1.625 5/8-18 26 17,470 .36 CAM-12 CAB-12 .7500 .875 .593 2.875 1.750 1.312 1.750 3/4-16 24 24,471 .57 Left Hand B + .064 - .013 W + .13 H Ref. A + .38 D Ref. Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand CAM-5 CAB-5 7.938 11.10 7.92 47.63 22.23 15.88 31.75 5/16-24 22 30,531 32 CAM-6 CAB-6 9.525 12.70 9.12 49.23 25.40 18.26 31.75 3/8-24 22 40,423 50 CAM-7 CAB-7 11.113 14.27 10.31 53.98 28.58 20.62 34.93 7/16-20 21 50,907 68 CAM-10 CAB-10 15.875 19.05 12.29 66.68 38.10 28.58 41.28 5/8-18 26 77,707 163 CAM-8 CAB-8 12.700 15.88 11.50 61.93 33.32 23.80 38.10 1/2-20 20 68,851 109 CAM-12 CAB-12 19.050 22.23 15.06 73.03 44.45 33.32 44.45 3/4-16 24 108,847 259 Body - Alloy steel, heat treated, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix as designated. Z Zerk type fitting Ex: CAM-6Z F Flush type fitting Ex: CAM-6F Load ratings apply only to rod ends without grease fittings. For load ratings with fittings, please consult our engineering department. *Grease fitting not available on this size. Studs available per notes and comments, page 78 *

www.aurorabearing.com • Fax 630-859-0971 15 VCAM & VCAB SERIES MALE ROD ENDS High Strength – Self Lubricating – Economy Series Left Hand B + .0025 - .0005 W + .005 H Ref. A ± .015 D Ref. Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Right Hand VCAM-5 VCAB-5 .3125 .437 .312 1.875 .875 .593 1.250 5/16-24 18 5,032 .07 VCAM-6 VCAB-6 .3750 .500 .359 1.938 1.000 .687 1.250 3/8-24 18 6,533 .11 VCAM-7 VCAB-7 .4375 .562 .406 2.125 1.125 .781 1.375 7/16-20 17 8,054 .15 VCAM-8 VCAB-8 .5000 .625 .453 2.438 1.312 .875 1.500 1/2-20 16 13,425 .24 VCAM-10 VCAB-10 .6250 .750 .484 2.625 1.500 1.062 1.625 5/8-18 22 14,755 .36 VCAM-12 VCAB-12 .7500 .875 .593 2.875 1.750 1.250 1.750 3/4-16 20 21,150 .57 Left Hand B + .064 - .013 W + .13 H Ref. A + .38 D Ref. Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand VCAM-5 VCAB-5 7.938 11.10 7.92 47.63 22.23 15.06 31.75 5/16-24 18 22,382 32 VCAM-6 VCAB-6 9.525 12.70 9.12 49.23 25.40 17.45 31.75 3/8-24 18 29,059 50 VCAM-7 VCAB-7 11.113 14.27 10.31 53.98 28.58 19.84 34.93 7/16-20 17 35,824 68 VCAM-8 VCAB-8 12.700 15.88 11.50 61.93 33.32 22.23 38.10 1/2-20 16 59,714 109 VCAM-10 VCAB-10 15.875 19.05 12.29 66.68 38.10 26.97 41.28 5/8-18 22 65,630 163 VCAM-12 VCAB-12 19.050 22.23 15.06 73.03 44.45 31.75 44.45 3/4-16 20 94,075 259 Body - Alloy steel, heat treated, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Bushing - Steel Backed, PTFE Composite Notes - All sizes available with studs upon request. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 16 BM & BB SERIES MALE ROD ENDS General Purpose - Precision (Light Duty) Left Hand B + .0015 - .0005 W + .000 - .005 H ± .005 A ± .015 D ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES Right Hand BM-3 BB-3 .1900 .312 .250 1.250 .625 .437 .750 10-32 13 1,169 .03 BM-4 BB-4 .2500 .375 .281 1.562 .750 .500 1.000 1/4-28 16 2,158 .04 BM-5 BB-5 .3125 .437 .344 1.875 .875 .625 1.250 5/16-24 14 2,784 .07 BM-6 BB-6 .3750 .500 .406 1.938 1.000 .719 1.250 3/8-24 12 3,915 .11 BM-7 BB-7 .4375 .562 .437 2.125 1.125 .812 1.375 7/16-20 14 4,218 .16 BM-8 BB-8 .5000 .625 .500 2.438 1.312 .937 1.500 1/2-20 12 6,660 .25 BM-10 BB-10 .6250 .750 .562 2.625 1.500 1.125 1.625 5/8-18 16 7,364 .38 BM-12 BB-12 .7500 .875 .687 2.875 1.750 1.312 1.750 3/4-16 14 11,518 .60 Body - Low carbon steel, protective coated for corrosion resistance. Race - Sintered brass, oil impregnated. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. Units are supplied without grease fittings. When grease fittings are required, specify by adding suffixes as designated. Z Zerk type fitting Ex: BM-6Z F Flush type fitting Ex: BM-6F Load ratings apply only to rod ends without grease fittings. For load ratings with fittings, please consult our engineering department. Left Hand B + .038 - .013 W + .00 - .13 H ± .13 A ± .38 D ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand BM-3 BB-3 4.826 7.92 6.35 31.75 15.88 11.10 19.05 10-32 13 5,197 13 BM-4 BB-4 6.350 9.53 7.14 39.67 19.05 12.70 25.40 1/4-28 16 9,600 20 BM-5 BB-5 7.938 11.10 8.74 47.63 22.23 15.88 31.75 5/16-24 14 12,385 33 BM-6 BB-6 9.525 12.70 10.31 49.23 25.40 18.26 31.75 3/8-24 12 17,416 51 BM-7 BB-7 11.113 14.27 11.10 53.98 28.58 20.62 34.93 7/16-20 14 18,759 73 BM-8 BB-8 12.700 15.88 12.70 61.93 33.32 23.80 38.10 1/2-20 12 29,624 113 BM-10 BB-10 15.875 19.05 14.27 66.68 38.10 28.58 41.28 5/8-18 16 32,752 173 BM-12 BB-12 19.050 22.23 17.45 73.03 44.45 33.32 44.45 3/4-16 14 51,237 273 Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 17 BW & BG SERIES FEMALE ROD ENDS General Purpose - Precision (Light Duty) Left Hand† B + .0015 -.0005 W + .000 - .005 H ± .005 A ± .015 D ± .010 K ± .010 J ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-2B ROD END NO. DIMENSIONS IN INCHES Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. BW-3 BG-3 .1900 .312 .250 1.062 .625 .406 .312 .437 .562 10-32 13 1,531 .04 BW-4 BG-4 .2500 .375 .281 1.312 .750 .469 .375 .500 .750 1/4-28 16 2,539 .06 BW-5 BG-5 .3125 .437 .344 1.375 .875 .500 .437 .625 .750 5/16-24 14 3,133 .09 BW-6 BG-6 .3750 .500 .406 1.625 1.000 .687 .562 .719 .937 3/8-24 12 3,915 .15 BW-7 BG-7 .4375 .562 .437 1.812 1.125 .750 .625 .812 1.062 7/16-20 14 4,218 .20 BW-8 BG-8 .5000 .625 .500 2.125 1.312 .875 .750 .937 1.187 1/2-20 12 6,660 .33 BW-10 BG-10 .6250 .750 .562 2.500 1.500 1.000 .875 1.125 1.500 5/8-18 16 7,364 .48 BW-12 BG-12 .7500 .875 .687 2.875 1.750 1.125 1.000 1.312 1.750 3/4-16 14 11,518 .72 Left Hand† B + .038 - .013 W + .00 - .13 H ± .13 A ± .38 D ± .25 K ± .25 J ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-2B ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams BW-3 BG-3 4.826 7.92 6.35 26.97 15.88 10.31 7.92 11.10 14.27 10-32 13 6,805 17 BW-4 BG-4 6.350 9.53 7.14 33.32 19.05 11.91 9.53 12.70 19.05 1/4-28 16 11,297 27 BW-5 BG-5 7.938 11.10 8.74 34.93 22.23 12.70 11.10 15.88 19.05 5/16-24 14 13,934 42 BW-6 BG-6 9.525 12.70 10.31 41.28 25.40 17.45 14.27 18.26 23.80 3/8-24 12 17,416 69 BW-7 BG-7 11.113 14.27 11.10 46.02 28.58 19.05 15.88 20.62 26.97 7/16-20 14 18,759 90 BW-8 BG-8 12.700 15.88 12.70 53.98 33.32 22.23 19.05 23.80 30.15 1/2-20 12 29,624 149 BW-10 BG-10 15.875 19.05 14.27 63.50 38.10 25.40 22.23 28.58 38.10 5/8-18 16 32,752 216 BW-12 BG-12 19.050 22.23 17.45 73.03 44.45 28.58 25.40 33.32 44.45 3/4-16 14 51,237 328 Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix as designated. Z Zerk type fitting Ex: BW-6Z F Flush type fitting Ex: BW-6F † Left hand units have identification groove near end of shank Body - Low carbon steel, protective coated for corrosion resistance. Race - Sintered brass, oil impregnated. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 18 MM & MB SERIES MALE ROD ENDS General Purpose - Precision (PTFE Liners Available) Left Hand B + .0015 - .0005 W + .000 - .005 H ± .005 A ± .015 D ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. ROD END NO. DIMENSIONS IN INCHES ** * * 3 3 3 ** * * 4 4 4 Right Hand MM-2 MB-2 .1250 .250 .187 .937 .500 .312 .562 6-321 16 502 .01 MM-3 MB-3 .1900 .312 .250 1.250 .625 .437 .750 10-32 13 1,169 .03 MM-4 MB-4 .2500 .375 .281 1.562 .750 .500 1.000 1/4-28 16 2,158 .04 MM-5 MB-5 .3125 .437 .344 1.875 .875 .625 1.250 5/16-24 14 2,784 .07 MM-6 MB-6 .3750 .500 .406 1.938 1.000 .719 1.250 3/8-24 12 3,915 .11 MM-7 MB-7 .4375 .562 .437 2.125 1.125 .812 1.375 7/16-20 14 4,218 .16 MM-8 MB-8 .5000 .625 .500 2.438 1.312 .937 1.500 1/2-20 12 6,660 .25 MM-10 MB-10 .6250 .750 .562 2.625 1.500 1.125 1.625 5/8-18 16 7,364 .38 MM-12 MB-12 .7500 .875 .687 2.875 1.750 1.312 1.750 3/4-16 14 11,518 .60 MM-14 MB-14 .8750 .875 .765 3.375 2.000 1.375 2.000 7/8-14 7 18,476 .91 MM-14-1 MB-14-1 .8750 .875 .687 3.375 2.000 1.312 1.875 7/8-14 12 22,843 .91 MM-16 MB-16 1.0000 1.375 1.000 4.125 2.750 1.875 2.125 1 1/4-12 17 43,541 2.41 MM-16-1 MB-16-1 1.0000 1.375 1.000 4.125 2.750 1.875 2.125 1-142 17 43,541 2.13 MM-16-2 MB-16-2 1.0000 1.375 1.000 4.125 2.750 1.875 2.125 1-12 17 43,541 2.13 Left Hand B + .038 - .013 W + .00 - .13 H ± .13 A ± .38 D ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-3A a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams ROD END NO. DIMENSIONS IN MILLIMETERS Right Hand MM-2 MB-2 3.175 6.35 4.75 23.80 12.70 7.92 14.27 6-321 16 2,236 6 MM-3 MB-3 4.826 7.92 6.35 31.75 15.88 11.10 19.05 10-32 13 5,197 13 MM-4 MB-4 6.350 9.53 7.14 39.67 19.05 12.70 25.40 1/4-28 16 9,600 20 MM-5 MB-5 7.938 11.10 8.74 47.63 22.23 15.88 31.75 5/16-24 14 12,385 33 MM-6 MB-6 9.525 12.70 10.31 49.23 25.40 18.26 31.75 3/8-24 12 17,416 51 MM-7 MB-7 11.113 14.27 11.10 53.98 28.58 20.62 34.93 7/16-20 14 18,759 73 MM-8 MB-8 12.700 15.88 12.70 61.93 33.32 23.80 38.10 1/2-20 12 29,624 113 MM-10 MB-10 15.875 19.05 14.27 66.68 38.10 28.58 41.28 5/8-18 16 32,752 173 MM-12 MB-12 19.050 22.23 17.45 73.03 44.45 33.32 44.45 3/4-16 14 51,237 273 MM-14 MB-14 22.225 22.23 19.43 85.73 50.80 34.93 50.80 7/8-14 7 82,185 411 MM-14-1 MB-14-1 22.225 22.23 17.45 85.73 50.80 33.32 47.63 7/8-14 12 101,601 411 MM-16 MB-16 25.400 34.93 25.40 104.78 69.85 47.63 53.98 1 1/4-12 17 193,670 1,091 MM-16-1 MB-16-1 25.400 34.93 25.40 104.78 69.85 47.63 53.98 1-142 17 193,670 965 MM-16-2 MB-16-2 25.400 34.93 25.40 104.78 69.85 47.63 53.98 1-12 17 193,670 965 Body - Low carbon steel, protective coated for corrosion resistance. No. 16 series standard body is alloy steel not heat treated. Race - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. Units are supplied without grease fittings. When grease fittings are required, specify by adding suffixes as designated. Z Zerk type fitting Ex: MM-6Z F Flush type fitting Ex: MM-6F T PTFE liner Ex: MM-6T Load ratings apply only to rod ends without grease fittings. For load ratings with fittings, please consult our engineering department. * Check availability. ** Grease fitting not available. 1 Threads 6-32 UNC. 2 Threads 1-14 UNS. 3 Tolerance variation: “D” ± .020, “A” ± .020, “B” + .0035, - .0005, “H” ± .010 4 Tolerance variation: “D” ± .51, “A” ± .51, “B” + .089, - .013, “H” ± .25 Studs available per notes and comments, page 78

www.aurorabearing.com • Fax 630-859-0971 19 MW & MG SERIES FEMALE ROD ENDS General Purpose - Precision (PTFE Liners Available) Left Hand† B + .0015 -.0005 W + .000 - .005 H ± .005 A ± .015 D ± .010 K ± .010 J ± .010 Ball Dia. Ref. C + .062 - .031 Thread UNF-2B ROD END NO. DIMENSIONS IN INCHES ** * * 3 3 3 Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Lbs. Approx. Brg. Wt. Lbs. MW-2 MG-2 .1250 .250 .187 .812 .500 .312 .250 .312 .437 6-321 16 1,202 .02 MW-3 MG-3 .1900 .312 .250 1.062 .625 .406 .312 .437 .562 10-32 13 1,531 .04 MW-4 MG-4 .2500 .375 .281 1.312 .750 .469 .375 .500 .750 1/4-28 16 2,539 .06 MW-5 MG-5 .3125 .437 .344 1.375 .875 .500 .437 .625 .750 5/16-24 14 3,133 .09 MW-6 MG-6 .3750 .500 .406 1.625 1.000 .687 .562 .719 .937 3/8-24 12 3,915 .15 MW-7 MG-7 .4375 .562 .437 1.812 1.125 .750 .625 .812 1.062 7/16-20 14 4,218 .20 MW-8 MG-8 .5000 .625 .500 2.125 1.312 .875 .750 .937 1.187 1/2-20 12 6,660 .33 MW-10 MG-10 .6250 .750 .562 2.500 1.500 1.000 .875 1.125 1.500 5/8-18 16 7,364 .48 MW-12 MG-12 .7500 .875 .687 2.875 1.750 1.125 1.000 1.312 1.750 3/4-16 14 11,518 .72 MW-14 MG-14 .8750 .875 .765 3.375 2.000 1.300 1.125 1.375 1.875 7/8-14 7 18,476 1.03 MW-14-1 MG-14-1 .8750 .875 .687 3.500 2.000 1.312 1.187 1.312 1.812 7/8-14 12 22,843 1.03 MW-16 MG-16 1.0000 1.375 1.000 4.125 2.750 1.625 1.500 1.875 2.125 1 1/4-12 17 40,889 2.13 MW-16-1 MG-16-1 1.0000 1.375 1.000 4.125 2.750 1.625 1.500 1.875 2.125 1-142 17 43,541 2.41 MW-16-2 MG-16-2 1.0000 1.375 1.000 4.125 2.750 1.625 1.500 1.875 2.125 1-12 17 43,541 2.41 Left Hand† B + .038 - .013 W + .00 - .13 H ± .13 A ± .38 D ± .25 K ± .25 J ± .25 Ball Dia. Ref. C + 1.57 - .79 Thread UNF-2B ROD END NO. DIMENSIONS IN MILLIMETERS ** * * 4 4 4 Right Hand a° Misalign. Angle Ultimate Radial Static Load Capacity Newtons Approx. Brg. Wt. Grams MW-2 MG-2 3.175 6.35 4.75 20.62 12.70 7.92 6.35 7.92 11.10 6-321 16 5,344 9 MW-3 MG-3 4.826 7.92 6.35 26.97 15.88 10.31 7.92 11.10 14.27 10-32 13 6,805 17 MW-4 MG-4 6.350 9.53 7.14 33.32 19.05 11.91 9.53 12.70 19.05 1/4-28 16 11,297 27 MW-5 MG-5 7.938 11.10 8.74 34.93 22.23 12.70 11.10 15.88 19.05 5/16-24 14 13,934 42 MW-6 MG-6 9.525 12.70 10.31 41.28 25.40 17.45 14.27 18.26 23.80 3/8-24 12 17,416 69 MW-7 MG-7 11.113 14.27 11.10 46.02 28.58 19.05 15.88 20.62 26.97 7/16-20 14 18,759 90 MW-8 MG-8 12.700 15.88 12.70 53.98 33.32 22.23 19.05 23.80 30.15 1/2-20 12 29,624 149 MW-10 MG-10 15.875 19.05 14.27 63.50 38.10 25.40 22.23 28.58 38.10 5/8-18 16 32,752 216 MW-12 MG-12 19.050 22.23 17.45 73.03 44.45 28.58 25.40 33.32 44.45 3/4-16 14 51,237 328 MW-14 MG-14 22.225 22.23 19.43 85.73 50.80 33.02 28.58 34.93 47.63 7/8-14 7 82,185 467 MW-14-1 MG-14-1 22.225 22.23 17.45 88.90 50.80 33.32 30.15 33.32 46.02 7/8-14 12 101,601 467 MW-16 MG-16 25.400 34.93 25.40 104.78 69.85 41.28 38.10 47.63 53.98 1 1/4-12 17 193,670 964 MW-16-1 MG-16-1 25.400 34.93 25.40 104.78 69.85 41.28 38.10 47.63 53.98 1-142 17 193,670 1,093 MW-16-2 MG-16-2 25.400 34.93 25.40 104.78 69.85 41.28 38.10 47.63 53.98 1-12 17 193,670 1,093 ** Grease fitting not available. Units are supplied without grease fittings. When a grease fitting is required, specify by adding suffix as designated. Z Zerk type fitting Ex: MW-6Z F Flush type fitting Ex: MW-6F T PTFE liner Ex: MW-6T * Check for availability † Left hand units have identification groove near end of shank 1 Threads 6-32 UNC 2 Threads 1-14 UNS 3 Tolerance variation: “D” ± .020, “A” ± .020 “B” + .0035, - .0005, “H” ± .010, “K” ± .015, “J” ± .015 4 Tolerance variation: “D” ± .51, “A” ± .51 “B” + .089, -.013, “H” ±.25, “K” ± .38, “J” ± .38 Body - Low carbon steel, protective coated for corrosion resistance. No. 16 series standard body is alloy steel not heat treated. Race - Low carbon steel, protective coated for corrosion resistance. Ball - Alloy steel, heat treated, hard chrome plated. Notes - All sizes available with studs upon request. Studs available per notes and comments, page 78

RkJQdWJsaXNoZXIy MTQzNjc=